No downloading service for updating is available.

Firmware Installer for BN-20

Firmware ver.2.00

Please download the execute file and follow the User's manual. This enables you to install the latest firmware to the printer.

BN20Firm200.exe (1.64MB) User's manual (202KB)

1.40 --- Latest version as of today

Firmware Installer for PRO2-series

Firmware ver.7.90

Please download the execute file and follow the User's manual. This enables you to install the latest firmware to the printer.

PRO2Firm790.exe (1.53MB) User's manual (202KB)

Firmware Installer for PRO3-series

Firmware ver.3.70

Please download the execute file and follow the User's manual. This enables you to install the latest firmware to the printer.

PRO3Firm380.exe (1.78MB) User's manual (202KB)

Firmware Installer for LEC-series

Firmware ver.4.80

Please download the execute file and follow the User's manual. This enables you to install the latest firmware to the printer.

LECFirm480.exe (1.79MB) User's manual (202KB)

Corrections for LEC-300

User's Manual

Some features concerning "INK RENEWAL" with LEC-300 have been modified to reduce the amount of the discharged ink significantly. ??In accordance with the modification above, the User's Manual must be updated. The respective locations of the changes and the contents affected by this modification in the manual are as follows. Please make sure to check them.

Locations of Changes Changed Contents Page 72 - 73 "4-5 Maintenance Tasks for White Ink" - The message of "INK RENEWAL RECOMMENDED" is not displayed. - The features concerning "INK RENEWAL NORMAL" and "INK RENEWAL FULL" are removed. If you cannot have the white ink normally discharged: (Please refer HERE to solve problems, such as dot drop-outs.) Page 123 - Before the modification - After the modification

Firmware Installer for LEJ-series

Firmware ver.1.30

Please download the execute file and follow the User's manual. This enables you to install the latest firmware to the printer.

LEJFirm130.exe (1.80MB) User's manual (202KB)

Firmware Installer for LEF-series

Firmware ver.1.50

Please download the execute file and follow the User's manual. This enables you to install the latest firmware to the printer.

LEFFirm150.exe (1.68MB) User's manual (202KB)

Firmware Installer for VS-series

Firmware ver.4.20

Please download the execute file and follow the User's manual. This enables you to install the latest firmware to the printer.

VSFirm420.exe (1.76MB) User's manual (202KB)

Firmware Installer for VP-series

Firmware ver.4.30

Please download the execute file and follow the User's manual. This enables you to install the latest firmware to the printer.

VPFirm430.exe (1.85MB) User's manual (202KB)

Firmware Installer for RS-series

Firmware ver.4.30

Please download the execute file and follow the User's manual. This enables you to install the latest firmware to the printer.

RSFirm430.exe (1.85MB) User's manual (202KB)

Firmware Installer for AJ-series

Firmware ver.4.50

Please download the execute file and follow the User's manual. This enables you to install the latest firmware to the printer.

AJFirm450.exe (1.6MB) User's manual (202KB)

Firmware Installer for RA-640

Firmware ver.1.20

Please download the execute file and follow the User's manual. This enables you to install the latest firmware to the printer.

RAFrim120.exe (1.69MB) User's manual (202KB)

Firmware Installer for RE-640

Firmware ver.1.20

Please download the execute file and follow the User's manual. This enables you to install the latest firmware to the printer.

REFrim120.exe (1.69MB) User's manual (202KB)

Firmware Installer for SP-i series

Firmware ver.1.80

Please download the execute file and follow the User's manual.

This enables you to install the latest firmware to the printer.

SPiFirm180.exe (1.84MB) User's manual (202KB)

Firmware Installer for SP-300 series

Firmware ver.7.30

Please download the execute file and follow the User's manual.

This enables you to install the latest firmware to the printer.

SP300Firm730.exe (1.6MB) User's manual (202KB)

Firmware Installer for SP-540V

Firmware ver.7.30

Please download the execute file and follow the User's manual.

This enables you to install the latest firmware to the printer.

SP540Firm730.exe(1.6MB) User's manual (202KB)

Firmware Installer for FP-series

Firmware ver.2.70

Please download the execute file and follow the User's manual.

This enables you to install the latest firmware to the printer.

FPFirm270.exe (1.67MB) readme (452KB)

Firmware Installer for SJ-1000 series

Firmware ver.2.80

Please download the execute file and follow the User's manual.

This enables you to install the latest firmware to the printer.

SJ1000Firm280.exe (1.62MB) readme (452KB)

Firmware

Firmware ver.5.40

Please download the exe file and follow the readme file.

fj50.exe (615KB) readme (452KB)

Firmware

Firmware ver.4.40

Please download the exe file and follow the readme file.

cj500.exe (668KB) readme (452KB)

Cut Driver

SP-540V Cut Driver for WindowsXP/2000

This is a driver for cutting only. It enables you to run cutting operation directly from a drawing software.

RWD047100.exe (217KB)

Cut Driver

SP-540V Cut Driver for WindowsVista

This is a driver for cutting only. It enables you to run cutting operation directly from a drawing software.

cutdriver_sp540.exe (343KB)

Windows Driver

Roland VersaCAMM Driver for Windows 2000/XP Ver 4.00

Please UNINSTALL the old Windows Driver in your PC.
You need to use "UnSetup.exe" for this uninstallation, which is included in a folder to be downloaded.
[OS] : Windows2000, WindowsXP

	Download an exe file on this page.
	Double-click the exe file to extract.
	Double-click "UnSetup.exe" in [RSP044v400JE] folder. Uninstallation program will start. Follow the messages on the screen.
	Double-click "Setup.exe." Installing program will start.

RSP044v400JE.exe (7.64MB)

Windows Driver

PC-12 ColorCAMM DRIVER for Windows2000/XP Ver.1.10

This is a non-PostScript GDI Driver.
You need to uninstall the current Windows Driver.

Unstallation
	Go to [Start] > [Printers and Faxes], then select an icon to delete.
	Click [File] > [Delete], then "OK".
	Click [File] > [Server Properties], then click a tab for "Driver."
	Select the driver to delete, click [Delete] and "OK."
Installation
	Download the exe file
	Double-click the exe file to extract.
	Double-click the "Setup.exe" in the folder. Then, follow the instructions.

d0411102kxp.exe (1.89MB)

Windows Driver

PC-600 ColorCAMM DRIVER for WindowsMe/98/95 Ver.1.20

This is a non-PostScript GDI Driver.
Roland ColorCHOICE cannot be in simultaneous operation.

	Download the exe file.
	Double-click the exe file to extract. Save it at a folder you like.
	Go to [Start] > [Settings] > [Printers and faxes] > [Add a printer]. "Welcome to the Add Printer Wizard" message will show up. Then, click [Next].
	"Select the option that describes the printer you want to use" will show up. Select "Local Printer" and click [Next].
	List of printers will show up, but there is not listed a "Roland". Click a button [Have disk...].
	Click [Browse...]. Then, select the "driver" and "folder" you extracted.
	Click [OK] twice. Then, the list of printer will have "Roland" listed.
	Select "PC-600" and click [Next].
	Select a Printer Port you are using. Then, follow the messages.

d035120j.exe (463KB)

Windows Driver

PC-600 ColorCAMM DRIVER for WindowsXP/2000/NT4.0 Ver.2.20

This is a non-PostScript GDI Driver.
Roland ColorCHOICE cannot be in simultaneous operation.
You need to uninstall the current Windows Driver.

Uninstallation
	Go to [Start] > [Printers and Faxes], then select an icon to delete.
	Click [File] > [Delete], then "OK".
	Click [File] > [Server Properties], then click a tab for "Driver."
	Select the driver to delete, click [Delete] and "OK."
Installation
	Download the exe file
	Double-click the exe file to extract. Save it at a folder you like.
	Go to [Start] > [Settings] > [Printers and faxes] > [Add a printer]. "Welcome to the Add Printer Wizard" message will show up. Then, click [Next].
	"Select the option that describes the printer you want to use" will show up. Select "Printer Port" that the printer is connected, and click [Next].
	List of printers will show up, but there is not listed a "Roland". Click a button [Have disk...].
	Click [Browse...]. Then, select the "driver" and "folder" you extracted.
	Click [OK] twice. Then, the list of printer will have "Roland" listed.
	Select "PC-600" and click [Next]. Then, follow the messages.

d038220j.exe (154KB)

Windows Driver

PC-60 ColorCAMM DRIVER for Windows3.1 Ver.1.80

Please follow the instruction described in "readme.txt" for installation.

d024180j.exe (163KB)

Windows Driver

PC-60 ColorCAMM DRIVER for WindowsMe/98/95 Ver.2.50

Please follow the instruction described in "readme.txt" for installation.

d025250j.exe (196KB)

Windows Driver

PC-60 ColorCAMM DRIVER for WindowsXP/2000/NT4.0 Ver.2.00

Please click your WindowsOS to refer installation procedure.

d033200j.exe (129KB)

WindowsXP *A limitation in length for printing may occur. You need to uninstall the current (old) Windows driver.
Uninstallation
	Go to [Start] > [Printers and Faxes], then select an icon to delete.
	Click [File] > [Delete], then "OK".
	Click [File] > [Server Properties], then click a tab for "Driver."
	Select the driver to delete, click [Delete] and "OK."
Installation Should be logged in as Administrator.
	Download the exe file.
	Double-click the exe file to extract. Save it at a folder you like.
	Go to [Start] > [Control Panel] > [Printers and faxes] > [Add printer] "Welcome to the Add Printer Wizard" message will show up. Then, click [Next].
	"Select the option that describes the printer you want to use" will show up. Select the printer's port and click [Next].
	List of printers will show up, but there is not listed a "Roland". Click a button [Have disk...].
	Click [Browse...]. Then, select the "driver" and "folder" you extracted.
	Click [OK] twice. Then, the list of printer will have "Roland" listed.
	Select "PC-60" and click [Next]. Then, follow the messages on the screen.

Windows2000, WindowsNT4.0 You need to uninstall the current (old) Windows driver. This is a non-PostScript GDI Driver. USB port is not supported in WindowsNT.
Uninstallation
	Go to [Start] > [Printers and Faxes], then select an icon to delete.
	Click [File] > [Delete], then "OK".
	Click [File] > [Server Properties], then click a tab for "Driver."
	Select the driver to delete, click [Delete] and "OK."
Installation Should be logged in as Administrator.
	Download the exe file
	Double-click the exe file to extract. Save it at a folder you like.
	Go to [Start] > [Settings] > [Printers] > [Add a printer]. "Welcome to the Add Printer Wizard" message will show up. Then, click [Next].
	"Select the option that describes the printer you want to use" will show up. Select "Local Printer" and click [Next].
	Select "Port" that the PC-60 is connected.
	List of printers will show up, but there is not listed a "Roland". Click a button [Have disk...].
	Click [Browse...]. Then, select the "driver" and "folder" you extracted.
	Click [OK] twice. Then, the list of printer will have "Roland" listed.
	Select "PC-60" and click [Next]. Then, follow the messages.

Windows Driver

PC-50 ColorCAMM DRIVER for Windows3.1 Ver.1.40

Please follow the instructions for installation described in the "readme.txt".

d019140j.exe (121KB)

Windows Driver

PC-50 ColorCAMM DRIVER for WindowsMe/98/95 Ver.1.80

Please follow the instructions for installation described in the "readme.txt".

d020180j.exe (89KB)

Windows Driver

ColorCAMM DRIVER for WindowsXP/2000/NT4.0 Ver.2.10

Please click your WindowsOS to refer installation procedure.

d032210j.exe (136KB)

WindowsXP *A limitation in length for printing may occur. You need to uninstall the current (old) Windows driver.
Uninstallation
	Go to [Start] > [Printers and Faxes], then select an icon to delete.
	Click [File] > [Delete], then "OK".
	Click [File] > [Server Properties], then click a tab for "Driver."
	Select the driver to delete, click [Delete] and "OK."
Installation Should be logged in as Administrator.
	Download the exe file.
	Double-click the exe file to extract. Save it at a folder you like.
	Go to [Start] > [Control Panel] > [Printers and faxes] > [Add printer] "Welcome to the Add Printer Wizard" message will show up. Then, click [Next].
	"Select the option that describes the printer you want to use" will show up. Select the printer's port and click [Next].
	List of printers will show up, but there is not listed a "Roland". Click a button [Have disk...].
	Click [Browse...]. Then, select the "driver" and "folder" you extracted.
	Click [OK] twice. Then, the list of printer will have "Roland" listed.
	Select "PC-60" and click [Next]. Then, follow the messages on the screen.

Windows2000, WindowsNT4.0 You need to uninstall the current (old) Windows driver. This is a non-PostScript GDI Driver. USB port is not supported in WindowsNT.
Uninstallation
	Go to [Start] > [Printers and Faxes], then select an icon to delete.
	Click [File] > [Delete], then "OK".
	Click [File] > [Server Properties], then click a tab for "Driver."
	Select the driver to delete, click [Delete] and "OK."
Installation Should be logged in as Administrator.
	Download the exe file
	Double-click the exe file to extract. Save it at a folder you like.
	Go to [Start] > [Settings] > [Printers] > [Add a printer]. "Welcome to the Add Printer Wizard" message will show up. Then, click [Next].
	"Select the option that describes the printer you want to use" will show up. Select "Local Printer" and click [Next].
	Select "Port" that the PC-60 is connected.
	List of printers will show up, but there is not listed a "Roland". Click a button [Have disk...].
	Click [Browse...]. Then, select the "driver" and "folder" you extracted.
	Click [OK] twice. Then, the list of printer will have "Roland" listed.
	Select "PC-60" and click [Next]. Then, follow the messages.

Windows Driver

PNC-5000 ColorCAMM DRIVER for Windows3.1 Ver.2.40

Please follow the instructions for installation described in the "readme.txt".

d006240j.exe (121KB)

Windows Driver

PNC-5000 ColorCAMM DRIVER for WindowsMe/98/95 Ver.2.80

Please follow the instructions for installation described in the "readme.txt".

d010280j.exe (89KB)

Macintosh Driver

Roland VersaCAMM Driver for MacintoshOS X Ver 4.00

Please follow the readme file which is included in the exe file to be downloaded.

VersaDrverv400(JPN)mac.sit (8.43MB)

Roland ColoRIP Updater

Roland ColoRIP Updater to ver.2.2

You need to have Roland COLORIP already installed.
This is updating program to the latest version 2.2 from 1.1~2.1x.
Before starting this updating program, quit operation of current Roland ColoRIP.

rcr22.zip (41.7MB) (Revision Record)

According as your internet connection speed, "divided" programs are available. 1. Click all the divided files, and save them all in one folder. 2. Double-click "rcr22.bat" file. The other files will be combined in one. 3. You will have a ZIP file. Then, follow the below instruction for how-to-install. rcr22.1 (5.0MB) rcr22.2 (5.0MB) rcr22.3 (5.0MB) rcr22.4 (5.0MB) rcr22.5 (5.0MB) rcr22.6 (5.0MB) rcr22.7 (5.0MB) rcr22.8 (5.0MB) rcr22.bat (1KB)

	Download a zip file on this page.
	Extract the zip file.
	Double-click "Install.exe" file in [COLORIP 2.2 Updater] folder. Updating program will start. Follow the messages on the screen.
	Click "Install" button. Installation starts.
	Select the destination folder as you prefer.
	Updating starts. Then, this message appears. Click "OK". You can trash the downloaded folder [COLORIP 2.2 Updater] which is no longer necessary.

Patch for ColorCHOICE 4.0/4.0A [Windows2000/NT]

Patch for Roland ColorCHOICE 4.0/4.0A for Windows2000/NT

This is a patch file to correct the program error.
Roland COLORCHOICE 4.0 does not start or "APP2.EXE ERROR" appears when the port setting is set to "TCP/IP print (LPR)" for a printer with network connected.

	Quit Roland ColorCHOICE if it is in operation.
	Double-click the exe file to extract.
	Overwrite the "CommonPorts.dll" file, which is located in [C:] > [Program Files] > [Roland COLORCHOICE 4] > [Program] > [Ports] .

win4rcc.exe (47KB)

Patch for ColorCHOICE 3.0E/3.1/3,1A/3.1B [Windows2000]

Patch for Roland ColorCHOICE 3.0E/3.1/3,1A/3.1B for Windows2000

This is a patch file to install PS driver to Windows2000. AdobePS driver is not supporting Windows2000. By this patch file (inf file), it can install PS driver by Microsoft. For installation, please refer to "rcc3win2k.pdf".

rcc3win2k.exe (25KB) rcc3win2k.pdf (159KB)

ColorCHOICE Updater for Windows

Roland ColorCHOICE for PC-12 ver.4.2B Updater

You need to have Roland ColorCHOICE 4.2/4.2A already installed.
This is updating program to the latest version 4.2B from 4.2/4.2A.
For WindowsXP, necessary to have the WindowsXP/2000/NT4.0 Driver ver.1.10 and above already installed.

Please follow the "RCCPC12win.pdf" for installation.

RCCPC12_up42B.exe (2.2MB) RCCPC12win.pdf (39KB)

ColorCHOICE Updater for Macintosh

Roland ColorCHOICE for PC-12 ver.4.2B Updater

You need to have Roland ColorCHOICE 4.2/4.2A already installed.
This is updating program to the latest version 4.2B from 4.2/4.2A.

Please follow the "RCCPC12mac.pdf" for installation.

RCCPC12_up42B.sea (1.8MB) RCCPC12mac.pdf (29KB)

Patch for ColorCHOICE 4.1B

dll file for Roland ColorCHOICE for ColorCAMM ver.4.1B

You need to have Roland ColorCHOICE 4.1B already installed.
This is a correction program for problems in Roland ColorCHOICE 4.1B.

• Problem 1 : When selecting "Grayscale(Resin)" or "Grayscale(Wax)" for the Color Mode, another ribbon than black one will be used.
• Problem 2 : RIPing cannot be completed when CMY (Resin, Wax) selected.

Overwrite the "AmRDGColorCAMM-PC-600.dll" file, which is loacted in [C:] > [ProgramFiles] > [RCC for ColorCAMM] > [OutputDrivers].

AmRDGColorCAMMPC600.dll (80KB)

Patch for ColorCHOICE 4.1B

dll file for Roland ColorCHOICE for ColorCAMM ver.4.1B

You need to have Roland ColorCHOICE 4.1B already installed.
This is a correction program for problems in Roland ColorCHOICE 4.1B.

• Problem 1 : When selecting "Grayscale(Resin)" or "Grayscale(Wax)" for the Color Mode, another ribbon than black one will be used.
• Problem 2 : RIPing cannot be completed when CMY (Resin, Wax) selected.

Overwrite the "AmRDGColorCAMM-PC-600.dll" file, which is loacted in [C:] > [ProgramFiles] > [RCC for ColorCAMM] > [OutputDrivers].

AmRDGColorCAMMPC600.DLL.hqx (128KB)

Local Updater for Roland VersaWorks

exe file for Roland VersaWorks Ver.4.60

*A USB Dongle key is required to run Roland VersaWorks.

This is to upgrade Roland VersaWorks whose PC is not online. You can download an execute file to upgrade it to the latest. Installer runs automatically when you double click the downloaded exe file.

When the version of your Roland VersaWorks is below 3.00, you need the two separate operations for upgrading. It needs to be upgraded to Ver.3.0 first by using RVWUpdater30.exe, and then you need another upgrade operation to the latest version.

RVWUpdater460 (325MB) -- Ver3.00 or above user RVWUpdater30.exe (420MB) -- below Ver3.00 user

Installer for Roland OnSupport

Roland OnSupport Ver.1.50

Download the Roland OnSupport Updater from this page. Refer to the Start Up Guide to install.

* This program functions as an installer.
Therefore, an attempt to install this program is failed if you have already installed the Roland OnSupport in your PC.
In case the Roland OnSupport is already installed, update the software using the updater.

ons_ins_150.zip (345MB) Start Up Guide

Updater for R-Works

R-Works Ver.1.01

Download the R-Works Updater from this page.

rworksupdater101.exe (114MB)

Updater for BN20 Win Utility

BN-20 Win Utility Ver.1.10

Download the BN-20 Win Utility Updater from this page.

BN-20WinUtility_V110.zip (4.78MB)

1.02---Latest Version as of Today